smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Samsung SpinPoint M8 (AF)
Device Model: ST500LM012 HN-M500MBB
Serial Number: S2ZYJ9CDC03488
LU WWN Device Id: 5 0004cf 20c0a94c8
Firmware Version: 2BA30001
User Capacity: 500 107 862 016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sat Dec 8 12:55:51 2018 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 6840) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 114) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 14
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 094 090 025 Pre-fail Always - 1966
4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 4020
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 5127
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 188
12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3321
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 1331
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 064 042 000 Old_age Always - 29 (Min/Max 8/58)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 100 100 000 Old_age Always - 3
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 80856
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 188
225 Load_Cycle_Count 0x0032 093 093 000 Old_age Always - 73608
SMART Error Log Version: 1
ATA Error Count: 5
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 5 occurred at disk power-on lifetime: 3756 hours (156 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 00 00 00 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
18 9f 18 9f 18 f0 18 9f 10:54:18.685 RECALIBRATE [RET-4]
00 00 00 00 00 00 00 08 00:00:00.016 NOP [Abort queued commands]
60 00 08 80 ef 08 40 08 00:00:00.017 READ FPDMA QUEUED
60 00 08 28 60 38 40 08 00:00:00.017 READ FPDMA QUEUED
60 00 08 28 5a 38 40 08 00:00:00.017 READ FPDMA QUEUED
Error 4 occurred at disk power-on lifetime: 3751 hours (156 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 00:00:02.866 IDENTIFY DEVICE
00 00 00 00 00 00 e0 08 00:00:02.866 NOP [Abort queued commands]
00 00 00 00 00 00 00 08 00:00:02.861 NOP [Abort queued commands]
61 00 60 80 4c 6f 40 08 00:00:02.866 WRITE FPDMA QUEUED
61 00 18 28 2e ad 40 08 00:00:02.866 WRITE FPDMA QUEUED
Error 3 occurred at disk power-on lifetime: 3751 hours (156 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 00 00 00 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
01 9f 18 9f 18 f0 18 9f 10:54:18.685 [RESERVED]
00 00 00 00 00 00 00 08 00:00:02.861 NOP [Abort queued commands]
61 00 60 80 4c 6f 40 08 00:00:02.866 WRITE FPDMA QUEUED
61 00 18 28 2e ad 40 08 00:00:02.866 WRITE FPDMA QUEUED
61 00 18 98 0e ae 40 08 00:00:02.866 WRITE FPDMA QUEUED
Error 2 occurred at disk power-on lifetime: 3751 hours (156 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 00 00 00 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
01 9f 18 9f 18 f0 18 9f 10:54:18.685 [RESERVED]
00 10 00 00 00 00 00 00 00:00:02.854 NOP [Reserved subcommand] [OBS-ACS-2]
61 00 88 00 a3 ac 40 00 00:00:02.857 WRITE FPDMA QUEUED
61 00 08 b0 ea 77 40 00 00:00:02.857 WRITE FPDMA QUEUED
61 10 10 e0 ea 77 40 00 00:00:02.857 WRITE FPDMA QUEUED
Error 1 occurred at disk power-on lifetime: 3751 hours (156 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 00:00:02.842 IDENTIFY DEVICE
00 00 08 00 58 a8 40 08 00:00:02.841 NOP [Abort queued commands]
61 00 08 00 58 a8 40 08 00:00:02.809 WRITE FPDMA QUEUED
61 00 08 00 58 a8 40 08 00:00:02.841 WRITE FPDMA QUEUED
ea 00 00 00 00 00 e0 08 00:00:02.839 FLUSH CACHE EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
